Stone Inlay Concrete Bench

Quikrete’s 5000 concrete mix is a great formula for building your own backyard bench.

This backyard bench is nearly indestructible. Once it’s cast, assembled and sealed, you can enjoy it all year long and never have to worry about taking it in for the winter or protecting it from the elements. I’ll guide you through the process of how I built my bench so you can use it as a guide to experiment with your own design ideas and personal touches to create your own garden bench.

A quick trip to the home center and you’ll be able to pick up just what you need for your bench. To build my bench, I used three bags of Quikrete 5000 to pour the top and both legs. These bags are heavy and weigh in at 80 lbs. each, so three bags will probably weigh about as much as your big Uncle Billy—certainly deliverable in a standard passenger car. Don’t substitute anything else for this mix. The 5000 formula has high early strength and will retain its integrity when you remove the forms and guarantee a sturdy, crack-free bench. Along with the 4-ft. lengths of rebar shown here, be sure you’ve got a mixing tub like the one shown here, or a wheelbarrow with a shovel, a garden hoe for mixing and a finishing trowel for smoothing. You’ll also need a half sheet of 3/4-in. plywood and a quarter sheet of 1/2-in. plywood. Here are some other incidentals you’ll need right away as well. Pick up some acrylic wood finish, some paste wax and a small box of 2-in. self-drilling wood screws (GRK fasteners). The materials will cost about $75.

See the attached drawings at the end of this text for the dimensions of the bench forms. Cut the form pieces with a table saw or a circular saw with a guide for consistent straight cuts. Assemble the form using 2-in. wood screws to secure the parts of the form. Some clamps will come in handy to help bend the pieces as you assemble.

The 3/4-in. plywood ends and the 1/2-in. plywood sides (flexibility is the key to the curved sides) are screwed to the 3/4-in.-thick base. Cut a 41-in. x 10-1/2-in. piece of 1/2-in. plywood to make the insert. Place the insert into the form and then make a scribing tool to follow the edge of the form and mark a line 3-1/2 in. from the form’s edge as show. The scribing tool is just a scrap of wood with a hole drilled into it for your pencil or marker. Cut the insert to size and then glue and screw it to the base.

Seal the interior of the form with acrylic varnish and let it dry. Then rub a film of paste wax over the inner form.

Measure and cut the 1/2-in. steel rebar to fit in the forms make sure the lengths are about 1-1/2 in. shy of each end of the form. Bend the forms into a gentle curve to follow the form’s contour. I used the fence post to gently bend the shape.

Cut the bases for the leg forms from 3/4-in. plywood and center and trace your plastic form insert. I used a 4-in. Snap Coupler for drainage pipe that I picked up at The Home Depot. The outside diameter is actually 5 in. You can use other shapes or even bend a round shape into an oval.

Cut and assemble the leg forms pieces according to the dimensions in Fig. C below. Glue the insert in with adhesive caulk or construction adhesive and let it dry overnight.

Brush on the acrylic varnish to cover the entire inner surface of the forms. Once it’s dry, apply the paste wax as you did with the form for the top.

Mix the concrete to the consistency shown above in your mixing tub or wheelbarrow. It should hold its shape when shoveled into the form, but should spread easily with a trowel. A runny mix is bad and will weaken the bench. The mix needs to be thick enough to keep its sand, stones and the rebar in suspension. Always wear protective clothing to avoid skin contact with wet concrete. Protective eyewear is a must.

Level the concrete into the forms to about two-thirds full. Don’t work the concrete too much. With concrete, less is more.

Gently hammer around the outside of the forms to bring the air bubbles to the surface. You also want some of the stones in the mix to settle to the bottom of the form. I used about 20 taps per side and bottom.

Lay the rebar into the concrete and then fill the form to the top with more concrete. If you haven’t mixed your second bag yet, do so. As long as you mix the concrete in closely timed sessions, they will bond together. The concrete can begin to set up in as little as an hour in warm weather, so stay on task.

Level the concrete with the form and tap gently again. Keep the pour in the shade and cover it with a plastic tarp until you’re ready to remove the form. Do not do this in direct sunshine.

Mix the rest of the concrete and then fill the leg forms in the same manner. Lay the concrete in as you go. Tap the legs about half as much as you did for the sides and bottom.

Mix the rest of the concrete and then fill the leg forms in the same manner. Lay the concrete in as you go. Tap the legs about half as much as you did for the sides and bottom.

Remove the forms for the top after about 40 hours. Unscrew one side at a time. Proceed gently, because the concrete is at a “green stage,” which means it’s still fairly fragile.

Tip the bench top on edge and tap gently and often to release the base portion of the form. This one will be stubborn because of the large surface area. Take your time.

I used a wire brush setup in my drill and gently removed the smooth concrete to reveal the aggregate below. Be gentle so you preserve the integrity of the surface.

As you can see, the stones that had settled to the bottom of the form are now exposed. Hose the top down with a firm spray of water from the garden hose and let the surface harden for another couple days.

Two days after the pour, remove the legs from their forms.

Pry the edges of the plastic insert, being careful not to mar the concrete surface. Score the plastic carefully with a utility knife to loosen it from the concrete.

Pull the insert out of the form with a pliers.

Smooth the rough edges of the bench legs and top with an abrasive. I used an old 100-grit sanding belt, but a tile-smoothing stone will work as well.

Lay out the materials you’ll need to make the inlay. Use a thin-set mortar that’ll work for exterior applications and find some stones or tile to inlay your design. I bought these at a local tile supply store, but you can use found stones as well. Just be sure your stones are all about the same height.

Mix the thin-set mortar to a peanut butter consistency and start setting the stones. It’s a good idea to practice a bit with the stones before you actually set them to get your brain oriented to the puzzle-like task.

Wipe off any drips of mortar because they will be difficult to remove if they set. You’ll need to wait till the next day to seal and then grout between the stones.

Apply a grout and stone sealer to the tops of the stones. This sealer will help keep the grout haze off the surface of the stones. Don’t get the sealer between the stones, only on the top. Wait a day before grouting.

Push the grout into the spaces between the stones, and let it set for an hour before wiping with a sponge.

Now you can get a feel for the finished look as you wipe the grout with a damp sponge. Don’t use too much water or the grout will weaken. Set the project aside for a few days before assembling. When assembling, use a landscape block adhesive to join the mating part. Do a dry run first, then mark the part locations and then apply the adhesive. Let the adhesive set for a day before you use your bench. After about four weeks, apply a concrete sealer to your bench top and sides to give it added protection from moisture and freeze cycles.


  • Site Comments

Write a comment